Battery - Move 1200 L
-
Stelos 800 L
Stelos: Safety Instructions – read before use | Environment Stelos: Firmware update Stelos: User Interface | Controls | Functions | Handling Stelos: Technical Data Stelos: Remote control | Flash triggering Stelos: Power supply | Battery Stelos: Maintenance | Repair | Warranty Stelos: Accessories & Spare Parts Stelos: Error messages
-
Satos
Satos: Safety Instructions – read before use | Environment Satos: Firmware update Satos Satos: User Interface | Controls | Functions | Handling Satos: Technical Data Satos: Remote control | Flash triggering Satos: Power supply | Battery Satos: Maintenance | Repair | Consumables | Spare parts | Guarantee Satos: Accessories Satos: Charging station for up to 4 slide-in batteries
- Pulso L
-
Siros S
Siros S: Safety Instructions – read before use | Environment Siros S: Firmware update Siros S: User Interface | Controls | Functions | Handling Siros S: Technical Data Siros S: Remote control | Flash triggering Siros S: Power supply Siros S: Maintenance | Repair | Consumables | Spare parts | Guarantee Siros S: Accessories
-
Siros L
Siros L: Safety Instructions – read before use | Environment Siros L: Firmware update Siros L Siros L: User Interface | Controls | Functions | Handling Siros L: Technical Data Siros L: Remote control | Flash triggering Siros L: Power supply | Battery Siros L: Maintenance | Repair | Consumables | Spare parts | Guarantee Siros L: Accessories
- Scoro E + S
- Move 1200 L
- RFS 2.1
- RFS 2.2
-
RFS 3
RFS 3: Safety Instructions – read before use | Environment RFS 3: Scope of delivery and operating elements RFS 3: User Interface | Controls | Functions | Handling RFS 3: Firmware Update RFS 3.0 RFS 3: Compatibility RFS 3: Technical Data RFS 3: Maintenance | Repair | Consumables | Spare parts | Guarantee RFS 3: Trouble shooting
- Pulso G, Unilite and Picolite
- LED F160
- Scope D50
- Compatibility (Lamp <-> light shaper | Lamp <-> power pack)
- Locate your distributor or dealer
-
Stelos 800 L
-
Satos
-
Pulso L
-
Siros S
-
Siros L
-
Scoro E + S
-
Move 1200 L
-
RFS 2.1
-
RFS 2.2
-
RFS 3
-
Pulso G, Unilite and Picolite
-
LED F160
-
Scope D50
-
Compatibility (Lamp <-> light shaper | Lamp <-> power pack)
-
Locate your distributor or dealer
Care of the lithium battery
During charging and discharging, the ambient temperature should be in the range +5 °C to +35 °C.
Use of the battery at very low temperatures may result in a severe loss of output.
The battery has a deep-sleep mode and switches itself off after 72 hours unless it is inserted into
a power pack so as to protect it against deep discharge. In this way the energy stored in the battery
is retained even after months without use.
To wake up the battery after 72 hours without use, press the "on" key on the battery’s front panel.
The type of battery used does not have a "memory effect", and so does not have to be discharged
regularly. It is, however, important to remember that the battery must not be discharged too far.
The unit switches off automatically when the battery voltage is too low. However, because there is a
small leakage current even when the unit is switched off, we strongly recommend that the battery
is recharged after use. The battery should be removed from the unit during long periods out of use.
In particular, please observe the following important information on the subject of care and maintenance
of the battery:
Important note: before the first startup, we recommend that you charge the battery. We also
recommend that you recharge the battery immediately after use, even if it is only partially discharged.
Avoid discharging the battery completely!
You will find further information on care of the battery on our website under
"Download" > "battery & care".
Charging the battery
The battery can be charged either installed in the unit or outside it. The unit can be operated while
it is charging.